SPECIFICATIONS


3.0L Engine

Description Capacities Type Part Number Global Part Number
Engine Oil With Filter 9 Quarts / 8.5 Liters We recommend you use 5W-40 synthetic engine oil such as Mopar that meets FCA Material Standard MS-12991 and the API SN engine oil category is required. 68231020AA 68231020GA
Cooling System * Engine: 14.5 Quarts / 13.7 Liters We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Material Standard MS.90032. 68163848AB 68163848GB
Fuel Selection 19.0 Gallons / 72.0 Liters Use good quality diesel fuel from a reputable supplier in your vehicle. Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system. For most year-round service, Number 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance. We recommend you use a blend of up to 5% biodiesel, meeting ASTM specification D-975 with your diesel engine. This vehicle is compatible with biodiesel blends greater than 5% but no greater than 20% biodiesel meeting ASTM specification D-7467 provided the shortened maintenance intervals are followed as directed. - -
AdBlueŽ Fluid Tank 5.1 Gallons / 19.3 Liters AdBlueŽ (Urea-Water Solution) According To DIN 70 070 and ISO 22241-1. - -
Diesel Exhaust Fluid (DEF) 5.1 Gallons / 19.3 Liters Mopar Diesel Exhaust Fluid (API Certified) (DEF) or equivalent that has been API Certified to the ISO 22241 standard. Use of fluids not API Certified to ISO 22241 may result in system damage. 68035704AC -
 
* Includes heater and coolant reservoir filled to MAX level.


NOTE: If the vehicle is exposed to extreme cold (below 20°F or -7°C), or is required to operate at colder-than-normal conditions for prolonged periods, use climatized Number 2 diesel fuel or dilute the Number 2 diesel fuel with 50% Number 1 diesel fuel. This will provide better protection from fuel gelling or wax-plugging of the fuel filters.

3.6L Engine

Description Capacities Type Part Number Global Part Number
Engine Oil With Filter 5 Quarts / 4.7 Liters We recommend you use API Certified SAE 0W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as Mopar, Pennzoil, and Shell Helix. Refer to your engine oil filler cap for correct SAE grade. 68218950AB 68218950GA
Cooling System * 13.0 Quarts / 12.3 Liters We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Material Standard MS.90032. 68163848AB 68218041GA
Fuel Selection 22 Gallons / 83 Liters 87 Octane (R+M)/2 Method, 0-15% Ethanol. — —
Spark Plugs GAP We recommend you use MOPAR Spark Plugs. — —
0.043 in / 1.1 mm
* Includes heater and coolant reservoir filled to MAX level.

A/C Refrigerant System

Description Charge Amounts Type Part Number Global Part Number
Refrigerant 1.06 Pounds / 482 Grams Use only refrigerant R-1234yf 68224028AA 68224028GA
Refrigerant Oil – FD46XG 05114554AC 05114554GC
Refrigerant Oil 5.0 oz / 150 ml Total System Fill – –
Refrigerant Oil 2.0 oz / 60 ml A/C Condenser – –
Refrigerant Oil 2.0 oz / 60 ml A/C Evaporator – –
Refrigerant Oil 1.0 oz / 30 ml A/C Receiver/Dryer – –
Refrigerant Oil (Refer to 24 - Heating and Air Conditioning/Plumbing/OIL, Refrigerant/Standard Procedure) A/C Compressor – –

TRANSMISSION

Description Capacities Type Part Number Global Part Number
Automatic
♦8HP50 9.5 Quarts/ 9 Liters Use only Mopar ZF 8&9 Speed ATF Automatic Transmission Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. 68218925AA 68218925GA
Manual
♦♦AL6 4.76 Pints/2.25 Liters We recommend you use Mopar ATF+4 Automatic Transmission Fluid. 68218057AB 68218057GC
♦ Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. Refer to the appropriate service information for the correct procedures.
♦♦ Approximate dry fill or fill to bottom edge of fill plug hole.

CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.


TRANSFER CASE

Description Capacities Type Part Number Global Part Number
♦ MP1622/MP1622-OR 3.38 Pints/1.6 Liters We recommend you use Mopar ATF+4 Automatic Transmission Fluid. 68218057AB 68218057GB
♦ MP3022C/MP3022C-OR 3.72 Pints/1.76 Liters We recommend you use Mopar ATF+4 Automatic Transmission Fluid. 68218057AB 68218057GB
♦ Approximate dry fill or fill to bottom edge of fill plug hole.

CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.


CHASSIS

Description Capacities Type Part Number Global Part Number
Axles (Front)
210 FBI (Model 44) - Front Axle 2.18 Pints/1.03 Liters We recommend you use Mopar Gear & Axle Lubricant (SAE 75W85) (API GL-5). 68378949AA 68378949GA
Axles (Rear)
♦♦ 220 RBI (Model 44) Rear Axle – Electronic Locker 3.06 Pints/1.45 Liters We recommend you use Mopar Gear & Axle Lubricant (SAE 75W85) (API GL-5). 68378949AA 68378949GA
♦/♦♦ 220 RBI (Model 44) Rear Axle – Limited Slip 2.87 Pints/1.36L Liters We recommend you use Mopar Gear & Axle Lubricant (SAE 75W85) (API GL-5). Models equipped with Trac-Lok Limited Slip Differential require a friction modifier additive. 68378949AA 68378949GA
Chassis Systems
Brake Master Cylinder N/A We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. 04318080AD 04318080GD
Clutch Master Cylinder N/A We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. 04318080AD 04318080GD
Power Steering Reservoir N/A We recommend you use MOPAR Electric Steering Pump Fluid 05154460AA 05154460GA
♦ Limited-Slip Rear Axles require the addition of 70 ml (2.37 oz.) MOPARŽ Limited Slip Additive.
♦♦ If equipped with Trailer Tow package use MOPARŽ Synthetic Gear Lubricant, SAE 75W-140 (04874469AA)

CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.